Hello. I'm new here
1 - 19 of 19 Posts
Joined
·
10 Posts
Added correct tire pressure yesterday and light didn't go out (drove over 10 miles) door jam says (factory OEM BRABUS Wheels) 26 up front and 36 in rear. Added exactly that. Must be a TPM sensor.
Grr...
Sent from my SM-N950U using Tapatalk
Grr...
Sent from my SM-N950U using Tapatalk
Joined
·
10 Posts
Joined
·
1,098 Posts
When you correct the tire pressure you need to press TMPS button on the button bank with the ignition switch on. That resets the TMPS light. Hold it in for a few seconds and the light flashes then resets. Make sure you have the right pressure in your tire when you reset because its the variance of a few pounds from the reset point pressure that triggers the light. The button is the farthest to the right. DCO
Joined
·
1,098 Posts
I have butt warmers, just not in the butt-on bank. Mine are aftermarket. DCO
Joined
·
10 Posts
Joined
·
36 Posts
Hey all, I have 2015 brabrus and would like to add a trailer. Any idea? Hope everyone is well. I live in the Mansfield area.
Joined
·
5,764 Posts
The Curt hitch is fairly easy to install. It is sold by U-haul as well as online. Curt says their hitch does not fit a Brabus. Probably because the hitch would come out behind the center outlet exhaust creating a burn hazard to anyone touching the trailer hitch on the hitch ball. I have one that I do not use with a trailer, only with a bike rack that fits in the receiver. I have never had a problem, but am aware that it gets hot after a while. Around town here, it is not a problem. I bought mine from www.etrailer.com/curt/hitch
The instructions indicate you should drill up thru the top of the frame, enlarge the hole so the bolt and washer can drop down inside the frame from above. Jill Hobbs husband discovered that the frame is open at the front and the locating spring guide wires are long enough enough to feed in from the front opening of the frame so you do not have to drill the extra hole in the frame. I am all for not drilling extra holes in the frame. I found it very easy to do.
The instructions indicate you should drill up thru the top of the frame, enlarge the hole so the bolt and washer can drop down inside the frame from above. Jill Hobbs husband discovered that the frame is open at the front and the locating spring guide wires are long enough enough to feed in from the front opening of the frame so you do not have to drill the extra hole in the frame. I am all for not drilling extra holes in the frame. I found it very easy to do.
Joined
·
5,764 Posts
It looks like etrailer has deleted the Brabus exclusion from their site. IF you want it done, U-haul will do it for a fee as they order, and sell Curt hitches.
Here are the instructions. Notice the Brabus exclusion at the top of their form.
https://assets.curtmfg.com/masterlibrary/110203/installsheet/CM_110203_INS.PDF
Here are the instructions. Notice the Brabus exclusion at the top of their form.
https://assets.curtmfg.com/masterlibrary/110203/installsheet/CM_110203_INS.PDF
Joined
·
1,663 Posts
Car Looks Great. If your are ready for a drive away from home with it you should think about the Skyline Drive event this weekend drive it down and back on Saturday 20 Oct. Lube up all your chassis pivot points to free up any ride harshness. And have a great time in your Smart.Just purchased a FourTwo Passion/Brabus trimmed 2013 around a month ago. *Waves*
Hello everyone.
Name is Dave and I'm from SW Ohio
Pic of car..![]()
Sent from my SM-N950U using Tapatalk
1 - 19 of 19 Posts
